PC-7® is a heavy duty paste epoxy with unlimited uses for bonding, sealing and filling that is designed for the tough job. Formulated for maximum strength, this paste epoxy allows ample working time for large jobs, and cures for service in 12-24 hours. You can shape and mold the epoxy and fill large gaps or voids easily. Simple 1:1 mix. Cured epoxy can be drilled, machined, tooled and painted. No job is too big for PC-7®. Bonds to unlike surfaces. “The Powerhouse of Repair Products.”
- Tremendous strength formulated for maximum bonding power
- Multi purpose paste epoxy that bonds to most surfaces.
- Non sag non drip makes vertical and overhead applications possible
- Ample working time for large and critical jobs
PC-7® is the tough job epoxy! This paste epoxy was formulated for maximum bonding power. When mixed, components A (grey) and B (black) reacts to form a bond of tremendous strength. PC-7® formulation provides extended working time, for large and critical jobs, which allow the user to reposition work or make changes. High “wet grab” or tack of PC-7® Paste Epoxy makes overhead and sidewall work easy without drip or sag. PC-7® demonstrates excellent chemical resistance to mild acids, caustics, detergents, gasoline, fuel oil, salt, and fresh water.
Bonds most everything to anything.
***Note: PC-7® will not bond to wax paper, Teflon®, Polyethylene, and some other plastics. There are hundreds of plastics in thousands of combination. Test a small area when in doubt.
Mixing Tips:
Approximately equal amounts of A and B by volume; variations of either component as high as 20%will not affect the bond strength. When desirable, one part of A to two parts B may be used to increase elasticity (expansion joints, etc.). In cold or cool temperatures, place PC-7® container near heat prior to using. PC-7® mixes and spreads easier at 80°F than at 40 F. Any clean smooth flat surface is an excellent surface for mixing and working. A small putty knife or flexible artist spatula are great tools for mixing and applying PC-7®.
***Note: Most epoxies are temperature sensitive and will cure faster at higher temperatures and slower at cooler temperatures. Speed cure with artificial heat.
Directions:
Using separate knives to remove amount needed, mix equal parts A (grey) and B (black) on flat clean surface until uniform color is achieved. Surfaces to be bonded must be free of dirt, oil, rust, etc. For best results, rough up the surface PC-7® will be bonding to. Normally, no vice or clamp needed. Prop or tape heavy objects to a wall or ceiling.
Applications:
Apply PC-7® Epoxy Paste in any thickness to both sides of surface and bring together firmly. Be careful to insure that ample amount of PC-7® remains between the contact surfaces. Use screen wire or fiberglass cloth to reinforce large voids and gaps.
Denatured alcohol is excellent for smoothing applied PC-7®. Also use Denatured alcohol to clean surfaces before applying.
After cure: Paint Drill, Machine, Sand, File, Tap, or Saw.
PC-7® has hundreds, if not thousands, of uses.
As Adhesive: Wood, Metal (all types), Glass, Brick, Block, Rubber, Concrete, Stone, Slate, Fiberglass, tile, and more in any and all combinations.
As Sealant: Oil, Gas, Water Tanks, Cellar Cracks, Pressure Tanks, and Plumbing Leaks.
As a Filler: Holes, Castings, Patterns, Molds, Voids, Welds, Steering Wheels and much more.
PC-7® is a heavy duty paste epoxy with unlimited uses for bonding, sealing and filling that is designed for the tough job. Formulated for maximum strength, this paste epoxy allows ample working time for large jobs, and cures for service in 12-24 hours. You can shape and mold the epoxy and fill large gaps or voids easily. Simple 1:1 mix. Cured epoxy can be drilled, machined, tooled and painted. No job is too big for PC-7®. Bonds to unlike surfaces. “The Powerhouse of Repair Products.”
- Tremendous strength formulated for maximum bonding power
- Multi purpose paste epoxy that bonds to most surfaces.
- Non sag non drip makes vertical and overhead applications possible
- Ample working time for large and critical jobs
PC-7® is the tough job epoxy! This paste epoxy was formulated for maximum bonding power. When mixed, components A (grey) and B (black) reacts to form a bond of tremendous strength. PC-7® formulation provides extended working time, for large and critical jobs, which allow the user to reposition work or make changes. High “wet grab” or tack of PC-7® Paste Epoxy makes overhead and sidewall work easy without drip or sag. PC-7® demonstrates excellent chemical resistance to mild acids, caustics, detergents, gasoline, fuel oil, salt, and fresh water.
Bonds most everything to anything.
***Note: PC-7® will not bond to wax paper, Teflon®, Polyethylene, and some other plastics. There are hundreds of plastics in thousands of combination. Test a small area when in doubt.
Mixing Tips:
Approximately equal amounts of A and B by volume; variations of either component as high as 20%will not affect the bond strength. When desirable, one part of A to two parts B may be used to increase elasticity (expansion joints, etc.). In cold or cool temperatures, place PC-7® container near heat prior to using. PC-7® mixes and spreads easier at 80°F than at 40 F. Any clean smooth flat surface is an excellent surface for mixing and working. A small putty knife or flexible artist spatula are great tools for mixing and applying PC-7®.
***Note: Most epoxies are temperature sensitive and will cure faster at higher temperatures and slower at cooler temperatures. Speed cure with artificial heat.
Directions:
Using separate knives to remove amount needed, mix equal parts A (grey) and B (black) on flat clean surface until uniform color is achieved. Surfaces to be bonded must be free of dirt, oil, rust, etc. For best results, rough up the surface PC-7® will be bonding to. Normally, no vice or clamp needed. Prop or tape heavy objects to a wall or ceiling.
Applications:
Apply PC-7® Epoxy Paste in any thickness to both sides of surface and bring together firmly. Be careful to insure that ample amount of PC-7® remains between the contact surfaces. Use screen wire or fiberglass cloth to reinforce large voids and gaps.
Denatured alcohol is excellent for smoothing applied PC-7®. Also use Denatured alcohol to clean surfaces before applying.
After cure: Paint Drill, Machine, Sand, File, Tap, or Saw.
PC-7® has hundreds, if not thousands, of uses.
As Adhesive: Wood, Metal (all types), Glass, Brick, Block, Rubber, Concrete, Stone, Slate, Fiberglass, tile, and more in any and all combinations.
As Sealant: Oil, Gas, Water Tanks, Cellar Cracks, Pressure Tanks, and Plumbing Leaks.
As a Filler: Holes, Castings, Patterns, Molds, Voids, Welds, Steering Wheels and much more.